内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

先进战斗机过失速机动大气数据融合估计方法

可控的过失速机动是先进战斗机超机动性能的重要标志，飞机飞行包线的扩大已超出传统的大气数据系统测量范围，可靠的迎角、侧滑角、总压、静压等飞行大气数据是制约先进战斗机过失速机动中飞行控制的关键因素。以中国推力矢量验证机为对象，基于过失速机动飞行试验的数据，开展大气参数估计与验证研究。结合过失速机动的时间与空间特性，研究了基于风速、地速、空速矢量和惯性姿态、导航参数的大气参数融合计算方法；针对过失速大迎角状态下飞机周围气流非定常、模型非线性导致的融合大气参数误差的复杂特性，进一步构建深度神经网络，对机动状态融合迎角、侧滑角的强非线性误差进行拟合。仿真和飞行试验表明：该方法可在大迎角飞行状态下实现主要大气参数的融合估计，过失速机动过程中融合迎角误差优于2.3°，融合得到的大气参数可为过失速大迎角机动飞行控制提供可靠的大气参数状态反馈。     

拦截高速目标的比例与反比例导引捕获区分析

针对拦截高速目标的作战特点，分析了比例导引(PN)与反比例导引(RPN)的捕获区。首先，通过分析拦截弹与目标的相对运动关系，推导得到了顺轨和逆轨的零控拦截条件，此条件由目标和拦截弹的速度前置角以及二者速度比确定；其次，以拦截弹和目标速度前置角为坐标系，推导得到了PN以及RPN捕获区以及各自导航比设置范围。PN的捕获区由逆轨零控拦截条件以及与其相切且斜率为1/(N-1)的两条直线构成，RPN的捕获区由顺轨零控拦截条件以及与其相切且斜率为1/(-N-1)的两条直线构成；然后，利用函数对称性将PN与RPN捕获区转换到同一坐标区间，得到了相同条件下RPN捕获区要大于PN捕获区的结论；最后，开展了四种情形下的仿真，验证了本文捕获区分析的合理性及有效性。     

差分卫星定位技术及其在武器系统中的应用

差分卫星定位系统可以极大地提高卫星定位的精度,但也有使用、维护复杂等缺点。针对差分卫星定位的特性,首先阐述了卫星差分定位的基本原理,分析了卫星定位误差源,并介绍了差分定位系统对各种误差的修正情况,然后介绍了差分定位系统的分类、方法及发展,其中详细介绍了在武器系统领域中应用较广的局域差分系统的各种方法及其优缺点;最后,对差分系统的实际应用进行了阐述,并重点探讨了其在进攻性武器及防御性武器领域实现应用的可行性。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

NiCrAl/Diatomite可磨耗封严涂层制备及性能

分别利用大气等离子喷涂技术制备了Ni/Al粘结底层、火焰喷涂技术制备了NiCrAl/Diatomite可磨耗封严涂层，研究了喷涂距离、送粉速率、火焰气体总流量、喷涂角度和氧燃比等喷涂参数对生长速率和涂层硬度的影响。结果表明，在较低的氧燃比条件下（O₂∶C₂H₂<1.6），随着喷涂距离的增大，涂层生长速率逐渐下降，硬度先保持不变后逐渐上升；当O₂∶C₂H₂>1.6时，涂层的生长速率会随着喷涂距离的增大先增大后减小，硬度随之逐渐下降。随着喷枪对基体相对移动速度的增大，涂层生长速率略微下降，硬度略有上升。气体总流量的增大使得涂层的生长速率明显上升，硬度明显下降。随着送粉量的增大，涂层生长速率明显提高，硬度随之先上升后下降。     

Effect of moderate geomagnetic storms on equatorial plasma bubbles over eastern Africa in the year 2012: Evolution and electrodynamics

Equatorial plasma bubbles (EPBs) are common features of the equatorial and low-latitude ionosphere and are known to cause radio wave scintillation which leads to the degradation of communication and navigation systems. Although these structures have been studied for decades, a full understanding of their evolution and dynamics remains important for space weather mitigation purposes. In this study, we present cases of EPBs occurrences around April and July 2012 geomagnetic storm periods over the African equatorial sector. The EPBs were observed from the Communications/Navigation Outage Forecasting System (C/NOFS) and generally correlated well to the ionospheric irregularities observed from the Global Positioning System total electron content (GPS-TEC) measurements (rate of TEC change, ROT). This study revealed that the evolution of the EPBs during moderate storms is controlled by the strength of the daytime equatorial electrojet (EEJ) currents regardless of the strength of the equatorial ionization anomaly (EIA), the latter is observed during the July storm case in particular. These effects were more evident during the main and part of the early recovery phases of the geomagnetic storm days considered. However, the evening hours TEC gradients between regions of the magnetic equator and ionization crests also played roles in the existence of ionospheric irregularities.     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

预测悬停旋翼跨音速流动的一种组合自由尾流/CFD方法

一种新的组合自由尾流 / CFD方法用于悬停旋翼流动的 CFD解中以考虑实际尾流的作用 .用文中描述的尾流分析方法研究了螺旋尖涡的运动 .首先从广义尾流模型开始 ,用半经验公式模化了涡核对旋翼尾流的作用 ;然后在环量收敛和尾迹收敛的条件下完成了自由尾迹计算 ;最后应用 Jameson有限体积龙格 -库塔推进格式求解了欧拉方程 .所得结果与相关文献和实验数据进行了比较